This error may be displayed on the configuration software V-SFT when data is transferred.
Possible causes and solutions are given below.

[When the transfer cable "USB" is used]

<Causes>

The USB ladder transfer function is being used but the following action is not taken (TS/V8 series only).

1. The Main Menu screen is not displayed.
   
   
2. "Ladder Transfer Setting" is not offline.

<Solutions>

1. Display the Main Menu screen.
   (Ladder communication is enabled on the RUN screen only.)
   
   
2. Open "Ladder Transfer Setting" and press [OFFLINE].
   The screen changes as follows when [OFFLINE] is pressed.
   
   

[When the transfer cable "Ethernet" is used]

<Causes>

1. The LAN cable is not connected.
   
   
2. "Disconnect" is displayed at the bottom left of the Main Menu → Ethernet screen.
   
   
3. The IP address set on the [Transfer]→[Communication Setting] dialog is not consistent with the IP address of the TSi/V series.
   
   
4. The PC and the TSi/V series are not on the same network.

<Solutions>

1. Check if the LAN cable is connected to the LAN connector correctly.
   
   
2. "Disconnect" displayed at the bottom left of the Main Menu → Ethernet screen must be changed to "Connect".
   
   
   • Depending on whether the hub is used or not, the cable type to use varies.
     Check the cable in use.
     - With hub: Straight cable
     - Without hub: Cross cable
     
     
   • When a hub is used, check the LED that indicates the hub link condition.
     If not lit, check the cable, and insert it into another empty port on the hub.
     
     
   • Turn on the hub again.
     
     
   • Check for errors in setting, such as exchanged data between the subnet mask and default gateway of the TSi/V series.

      

3. Check the IP address of the TSi/V series on the Main Menu → Ethernet screen, and set it on the [Transfer]→[Communication Setting] dialog.
   
   
   
   
4. Check a ping from the PC to the TSi/V series.
   If not pinged, check the IP addresses of the PC and the TSi/V series.
   
   Example: When checking or changing the IP address of the PC
   

[When the transfer cable "V-CP" is used]

<Causes>

1. The transfer cable "V-CP" is not connected correctly.
2. The COM port number set on the [Transfer]→[Communication Setting] dialog is not consistent with the COM port number of the PC.
3. MJ1 is being used for another function; however, the Main Menu screen is not displayed.
4. "Editor : MJ1" is not displayed at the bottom left of the Main Menu screen.
5. "Modem Connect Mode" is displayed at the bottom left of the Main Menu screen.

<Solutions>

1. Check if the transfer cable "V-CP" is connected correctly to the MJ1 port of the TS2060/V series.
    * MJ2 port cannot be used for transfer.
   
   
2. Check the COM port number using the Device Manager of the PC, and set this port number for [Communication Port] on the [Transfer] →[Communication Setting] dialog.
   
   [COM port on the PC]
   Example: When USB-serial converter is used:
   

1. 
   [Communication Setting] dialog
   
   
   
2. When MJ1 is being used for another function as well, be sure to display the Main Menu screen before data transfer.
   
   
3. When the serial ladder transfer function is being used, the indication at the bottom left of the Main Menu screen changes to "Editor : ---".
   Hold down the function switch [F2] until "Editor : MJ1" is displayed, then transfer data again.
   
   
   Example: V8 series
   
   Screen transfer not possible (ladder transfer possible)
   
   
   Screen transfer possible
   
   

    

   To keep "Editor : MJ1" at the bottom left of the Main Menu screen at all times, set the screen data as shown below.

    

   TS/V8 series
   Click  [System Setting] → [Hardware Setting] → [Ladder Transfer] .
   

   Check [Detail Setting] →  [Ladder Communication is not Used in Local Mode] on the [Ladder Transfer Setting] dialog.
   
   

   V7 series
   Select [System Setting] → [Extended Communication] → [Ladder Tool] and check [Ladder Communication is not Used in Local Mode].
   
   

    

4. When "Modem Connect Mode" is displayed, press the function switch [F5] and "Editor : MJ1" at the same time to switch to the Extended Function Setting screen.
   Select "Not used" for [Modem Comm. Baud Rate] and press [Setting Finished] to move back to the Main Menu screen.
   When "Modem Connect Mode" is not displayed, transfer data again.
   For more information on the procedure, click here.